Search found 16 matches

by nedpicaxe
Tue Jun 25, 2019 9:00 am
Forum: Our Main Discussion Forum
Topic: infrared control of servo
Replies: 4
Views: 138

Re: infrared control of servo

Hi Ross.
A bit strange but I am not going to worry about it to much. My Email address is ..... I have not got yours. I have learnt a lot during the project. Using 4066 switches and using cmos inverters as amplifiers. Regards Nedpicaxe
by nedpicaxe
Sun Jun 23, 2019 9:12 am
Forum: Our Main Discussion Forum
Topic: infrared control of servo
Replies: 4
Views: 138

Re: infrared control of servo

Hello macservice 123 Somehow your post of what has turned out as (Infrared control of servo} is somehow one of my earlier posts of mine dated Sun June 10 2018. It might be a system software problem that has caused this. My Password ends in 123 and may have caused some confusion with the controlling ...
by nedpicaxe
Wed May 08, 2019 8:07 am
Forum: Projects & Photos
Topic: Hbridge diagram corrections
Replies: 1
Views: 107

Re: Hbridge diagram corrections

I correct another mistake in the post. They should be picaxe OM82 micro controllers Regards Nedpicaxe.
by nedpicaxe
Mon May 06, 2019 7:51 am
Forum: Projects & Photos
Topic: Hbridge diagram corrections
Replies: 1
Views: 107

Hbridge diagram corrections

My previous posts on H Bridge drivers are in error over the picaxe micro controller type. They should picaxe OM82. Because the posted diagrams are jpeg they cannot be edited or updated without deleting them and starting again. Regards Nedpicaxe.
by nedpicaxe
Thu Apr 18, 2019 11:49 am
Forum: Projects & Photos
Topic: H Bridge on breadboard
Replies: 0
Views: 115

H Bridge on breadboard

Previous circuit on breadboard. Notice motor voltage can go much higher than the picaxe 5volts
by nedpicaxe
Wed Apr 17, 2019 8:38 am
Forum: Projects & Photos
Topic: H Bridge motor drivers revisited
Replies: 0
Views: 82

H Bridge motor drivers revisited

Here is a picaxe driven motor with a higher voltage than the picaxe 5volts.
I am not sure whether I can get both pictures on the one post if aImage[/img]ny. I will persevere anyway RImageegards NedpicaxeImage
by nedpicaxe
Thu Feb 07, 2019 8:29 am
Forum: Our Main Discussion Forum
Topic: Picaxe Revolution Education output Device 8
Replies: 0
Views: 80

Picaxe Revolution Education output Device 8

I will have a go at controlling a Standard Control Servo using the Picaxe method in section 8 of the Microcontroller interfacing circuits in the Revolution Education Manual. I will try Infrared as the transmission between the remote and the servo circuit. Here is Hoping Regards Nedpicaxe
by nedpicaxe
Wed Jan 30, 2019 8:25 am
Forum: Our Main Discussion Forum
Topic: Dragging images on to message box
Replies: 5
Views: 265

Re: Dragging images on to message box

Thank you timchpi. for the reply Yes photos or wiring diagrams all in the jpeg format. Regards Nedpicaxe
by nedpicaxe
Fri Jan 18, 2019 8:09 am
Forum: Our Main Discussion Forum
Topic: Dragging images on to message box
Replies: 5
Views: 265

Re: Dragging images on to message box

Thank U for the replys They are Jpg images. Three of them posted well. but I cant recall which method I used Then after that no luck with dragging. I am from Whanganui. I used to get great results from the old system but I will persevere with this new one as I have many projects to work on and post ...
by nedpicaxe
Sat Jan 05, 2019 10:10 am
Forum: Our Main Discussion Forum
Topic: Dragging images on to message box
Replies: 5
Views: 265

Dragging images on to message box

I have tried dragging photos on to the message box and they just disappear. I have tried clearing the cache and there is so many options and unclear instructions that I cant get any sense or results. Typical of Windows 10. I will have a go at the other computer using Windows 7 and see how I get on. ...